SAM4S SPS2200

EPROM DOWNLOAD VERSION 1.17

https://www.dropbox.com/s/4gtvtkc6mhpxtof/update.zip

TO TURN THE MACHINE ON

OPEN THE FLAP ON THE RIGHT HAND SIDE TO EXPOSE THE POWER ROCKER SWITCH.

HOLD THE POWER BUTTON LOCATED UNDER THE BOTTOM RIGHT HAND CORNER OF THE SCREEN WHILST PRESSING THE POWER ROCKER SWITCH.

TO FIT THE DALLAS KEY READER AND MSR READER REMOVE THE BLANKING PLATE ON THE RIGHT HAND SIDE OF THE MACHINE.

THE MSR READER BEFORE INSTALLATION NEEDS PLUGGING INTO A SPT4700 AND PROGRAMMING BUT INSTEAD OF %DALL THAT NEEDS CHANING TO @

ONCE THIS READER IS INSTALLED GO INTO THE S-MODE PROGRAMMING CHOOSE SYSTEM OPTIONS THEN CHOOSE OPTION 5 TAB

SET DALLAS READER TO YES.

TO CHECK THE DALLAS AND MSR CHOOSE THE SELF TEST THEN SELECT MSR AND SWIPE A CARD TO TEST.

TO TEST THE DALLAS READER CHOOSE DALLAS READER THEN PUT A MAG FOB ON THE READER.

TO SELECT A DRAWER EITHER 12 OR 24 VOLT PRESS THE DRAWER BUTTON THEN PUT A TICK IN THE 12 OR 24V OPTION

 To upgrade the eprom you will need the latest sps2200 upgrade file and an sd card will be needed

 

Inset SD Card

 

Hold front Power button and switch on until a pink flash is shown on screen.

 

You should ne see a password screen.

 

Enter 1287

 

Select the ‘UPDATE’ option at the bottom of the screen menu.

 

Select ‘COPY ALL – SD’

 

Once this has updated select ‘KERNAL – SD’

 

Once this has updated select ‘APP UPDATE’

 

Select ‘YES’

 

This will take you to a different menu.

 

Select ‘SD – ALL UPDATE’

 

This will now update the Software.

 

After the update the calibration will show on screen, follow this through.

 

The Register screen will load up but it is not ready to us.

 

Now do a Ram Clear on the machine by entering the ‘1287’ Menu again and selecting ‘ALL CLEAR’

 

After the reset has been done the 2200 should be ready to use.

 

To check the right software has been loaded;  Service Mode > Self Test > Version. Below I have listed the correct software version that should have been updated;

 

 

Application Version : V1.17 YCR(APR.21.2014)

Kernal Version : Linux 2.6.28.6 – SPS2200 – V1.06 (Jan 7 2014)

Ram Disk Version : SPS2200 – RFS V1.12 (MAR 28 2012)

Bootloader F/W Version : SPS-2200 FW Version 1.05 June. 27. 2013

Bootloader UBoot Version : U-Boot 1.3.4 Mar.07.2012 for SAM4S SPS-2200 1.02

 

SPS 2200 SHELF EDGE LABEL PRINTING

GOTO PGM

SYSTEM OPTION THEN PRESS PAGE DOWN

CHOOSE GENERAL PRINTING OPTION

CHOOSE OPTION PAGE 8

SET ENABLE BARCODE PRINTING OPTION TO YES

CLOSE – CLOSE

CHOOSE PLU

PRESS PAGE DOWN

CHOOSE SELF PRINT BARCODE FORMAT

SET BARCODE HEIGHT TO 100

SET BARCODE WIDTH TO 4

SET BARCODE PRINTER PORT TO THE PRINTER PORT

SET FEED LINE TO 4

SET PRINT PLU CODE – PRICE WITH BARCODE AND NAME WITH BARCODE TO YES

SET JUSTIFICATION TO CENTRE

SET DEFAULT BARCODE TYPE TO BARCODE TYPE 1

CLOSE

THEN USE ADD AND CHANGE SCAN THE ITEM THEN PRESS PRINT BARCODE

 

TO BACKUP AND RESTORE SPS 2200 TO MEMORY PEN

BACKUP

1 INSERT MEMORY PIN INTO USB DRIVE

2 SELECT S MODE ON THE MACHINE

3 PRESS THE PROGRAM BACKUP BUTTON

4 PRESS THE USB BUTTON

5 PRESS THE NEW BUTTON

6 TYPE THE NAME OF THE STORE EG SPSSCALELINK PRESS OK

7 PRESS THE OPEN BUTTON

8 PRESS BACKUP PROGRAM TO USB

9 PRESS YES

10 THEN PRESS YES TO ARE YOU SURE

11 PRESS CLOSE

 

RESTORE

1 INSERT THE MEMORY PEN

2 SELECT S MODE

3 PRESS PROGRAM BACKUP THEN PRESS USB

4 PRESS THE NAME OF THE STORE EG SPSSCALELINK

5 PRESS RESTORE PGM FROM USB

6 PRESS ALL

7 PRESS CLOSE

Langley Distribution has written 42 articles